Extraction of Friction Coefficient for Spline Tooth Surfaces based on MB Fractal Contact Model and Ultra-Depth-of-Field Topography

Authors

  • Tenglang Luo College of Mechanical and Electrical Engineering, Shaanxi University of Science and Technology, Xi'an 710021, Shaanxi, China
  • Jinsheng Liang College of Mechanical and Electrical Engineering, Shaanxi University of Science and Technology, Xi'an 710021, Shaanxi, China
  • Min Zhang College of Mechanical and Electrical Engineering, Shaanxi University of Science and Technology, Xi'an 710021, Shaanxi, China

DOI:

https://doi.org/10.6919/ICJE.202611_12(11).0012

Keywords:

Spline Rotor; MB Fractal Contact Model; Friction Coefficient; Surface Topography; Power Spectrum Method; Ultra-Depth-Of-Field Microscopy.

Abstract

In the dynamic modeling of spline rotors, the friction coefficient is often assigned a fixed empirical value, which fails to reflect the regulatory effect of microscopic tooth surface morphology on friction behavior. To address this issue, this paper relies on the Majumdar-Bhushan (MB) fractal contact theory, incorporating the adhesion effect and plowing effect into a unified framework to establish a quantitative mapping relationship between the friction coefficient and the tooth surface fractal characteristic parameters (fractal dimension D, scale coefficient G). With the aid of an ultra-depth-of-field optical microscope, three-dimensional topography was collected from 6 tooth surface regions of three sets of spline specimens from the same batch. From these, 18 one-dimensional profile curves were intercepted, and the fractal dimension and scale coefficient were calculated individually using the power spectrum method, which were then substituted into the model for numerical solution of the equivalent friction coefficient. The results show that the tooth surface roughness Ra ranges from 1.106 to 4.471 μm, the fractal dimension D ranges from 1.234 to 1.643, and Roughness peak G* ranges from 5.783×10⁻⁶ to 1.150×10⁻⁵. The calculated friction coefficient μ falls within the range of 0.07 to 0.25, which is highly consistent with the empirical range for ground tooth surfaces (0.05 to 0.3). The above work provides a pathway for determining the friction coefficient that accounts for surface topography effects for spline rotor dynamic models, effectively avoiding the blindness of empirical value assignment.

Downloads

Download data is not yet available.

References

[1] Ratsimba, C. H. H., McColl, I. R., Williams, E. J., Leen, S. B., & Soh, H. P. (2004). Measurement, analysis and prediction of fretting wear damage in a representative aeroengine spline coupling. Wear, 257(11), 1193–1206. https://doi.org/10.1016/j.wear.2004.08.003

[2] Zhao, G., Zhao, X. Y., Qian, L. T., Yuan, Y., Ma, S., & Guo, M. (2022). A review of aviation spline research. Lubricants, 11(1), Article 6. https://doi.org/10.3390/lubricants11010006

[3] Beam, A. S. (1959). The advantages of involute spline and serrations from a gaging standpoint. SAE Technical Paper, 590200. https://doi.org/10.4271/590200

[4] Majumdar, A., & Bhushan, B. (1991). Fractal model of elastic-plastic contact between rough surfaces. Journal of Tribology, 113(1), 1–11. https://doi.org/10.1115/1.2920588

[5] Majumdar, A., & Tien, C. L. (1990). Fractal characterization and simulation of rough surfaces. Wear, 136(2), 313–327. https://doi.org/10.1016/0043-1648(90)90154-3

[6] Warren, T. L., & Krajcinovic, D. (1996). Random cantor set models for the elastic-perfectly plastic contact of rough surfaces. Wear, 196(1–2), 1–15. https://doi.org/10.1016/0043-1648(95)06785-X

[7] Majumdar, A., & Bhushan, B. (1991). Fractal model of elastic-plastic contact between rough surfaces. Journal of Tribology, 113(1), 1–11. https://doi.org/10.1115/1.2920588

[8] Bowden, F. P., & Tabor, D. (1964). The friction and lubrication of solids. Clarendon Press.

[9] Ge, S. R., & Zhu, H. (2005). Fractal theory of tribology. China Machine Press.

Downloads

Published

2026-11-15

Issue

Section

Articles

How to Cite

Luo, T., Liang, J., & Zhang, M. (2026). Extraction of Friction Coefficient for Spline Tooth Surfaces based on MB Fractal Contact Model and Ultra-Depth-of-Field Topography. International Core Journal of Engineering, 12(11), 101-115. https://doi.org/10.6919/ICJE.202611_12(11).0012