Physical Properties and Continuous Cleaning Process Design for Sea Cucumber Hatchery Mesh-Panel Substrates
DOI:
https://doi.org/10.6919/ICJE.202611_12(11).0010Keywords:
Sea Cucumber Hatchery; Mesh-Panel Settlement Substrate; Tensile Force; High-Pressure Water Jet; Vibration Dewatering.Abstract
Rope-strung polyethylene mesh panels are widely used as settlement substrates in Japanese sea cucumber (*Apostichopus japonicus*) hatcheries. Uneaten feed, feces and deposited particles accumulate on panel surfaces, in mesh openings and between layers, making manual rinsing, draining and air-drying labor-intensive and restricting throughput expansion during peak hatchery seasons. To provide a basis for designing a continuous production line for cleaning sea cucumber hatchery substrates, field surveys and laboratory measurements were carried out on substrates collected from commercial hatcheries in Dalian, China. The geometry of typical assemblies was recorded; single-strand nylon connecting ropes and polyethylene monofilaments were tensile-tested at 100 mm/min; wet assemblies were oven-dried at 120 °C to determine drying mass loss and wet-basis moisture content; and fouling deposits were sampled for pH, moisture content and wet density. The results show that typical assemblies contain 7–10 mesh layers, with unfolded panels 430–480 mm long and 360–400 mm wide, mesh openings of 0.5–0.7 mm × 0.6–0.8 mm and monofilaments 0.26–0.28 mm in diameter. The breaking forces of nylon strands and polyethylene monofilaments are (357.65 ± 21.64) N and (16.38 ± 1.35) N, respectively. The mean drying mass loss per assembly is 110.00 g, corresponding to a wet-basis moisture content of (25.21 ± 1.11)%. On this basis, a continuous process line was designed integrating overhead-chain conveyance with panel guiding, staggered two-sided high-pressure water-jet cleaning, vibration dewatering, hot-air drying and automatic unhooking and counting; the cleaning wastewater is treated by trough collection, screen filtration and settling. The line throughput and hot-air water-removal load are linked to hook pitch, chain speed and the residence time of each station, providing an initial basis for station layout and prototype parameter commissioning.
Downloads
References
[1] Li, L., Li, Q., & Kong, L. (2010). The effect of different substrates on larvae settlement in sea cucumber, Apostichopus japonicus Selenka. Journal of the World Aquaculture Society, 41, 123–130. https://doi.org/10.1111/j.1749-7345.2010.00345.x
[2] Song, Q. (2023). Development of cleaning equipment for Japanese sea cucumber settlement substrates. (Master’s thesis). Dalian Ocean University.
[3] Dalian Zhiyan Fishery Technology Co., Ltd., & Dalian Ocean University. (2024, April 26). A sea cucumber hatchery net cleaning machine (Chinese Patent No. CN201911146785.2).
[4] Bloecher, N., Frank, K., Bondø, M., et al. (2019). Testing of novel net cleaning technologies for finfish aquaculture. Biofouling, 35(7), 805–817. https://doi.org/10.1080/08927014.2019.1663413
[5] Li, S. Y., Ye, H. C., Wang, Z. H., et al. (2024). Effectiveness of water-jet cleaning and associated damage to micro-irrigation filter screens. Journal of Drainage and Irrigation Machinery Engineering, 42(1), 102–108. https://doi.org/10.3969/j.issn.1674-8530.22.0192
[6] Möllnitz, S., Feuchter, M., Duretek, I., et al. (2021). Processability of different polymer fractions recovered from mixed wastes and determination of material properties for recycling. Polymers, 13(3), 457. https://doi.org/10.3390/polym13030457
[7] Cripps, S. J., & Bergheim, A. (2000). Solids management and removal for intensive land-based aquaculture production systems. Aquacultural Engineering, 22(1/2), 33–56. https://doi.org/10.1016/S0144-8609(00)00031-5
Downloads
Published
Issue
Section
License
Copyright (c) 2026 International Core Journal of Engineering

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.




