Simulation Optimization of Hopper and Agitator Parameters for Powder Feeding Device based on EDEM
DOI:
https://doi.org/10.6919/ICJE.202611_12(11).0004Keywords:
Powder Quantitative Feeding; Discrete Element Method; Hopper Taper Angle; Agitator Rotational Speed; Granular Flow; Screw Feeding.Abstract
Aiming at the problems of poor discharging performance and insufficient feeding capacity of powder quantitative feeding devices, coarse coffee granules with a diameter of 1 mm were taken as the research object. The discrete element method (EDEM) was adopted to simulate the feeding process of the screw feeder, and the effects of hopper taper angle, agitator installation and agitator rotational speed on particle velocity and outflow rate at the hopper outlet were investigated. The Hertz‑Mindlin (no‑slip) contact model was employed. The time step was set to 15%‑20% of the Rayleigh time step. The minimum particle velocity, maximum particle velocity, mean particle velocity at the outlet section and the number of discharged particles within 0.05 s were selected as evaluation indices. The results show that the hopper taper angle imposes a remarkable influence on discharging capacity. At a taper angle of 60°, the mean outlet particle velocity reaches 199.9 mm/s and the number of discharged particles is 8 667, both being the maximum values among all schemes; the number of discharged particles increases by 3.1%‑12.9% compared with other taper angles. By contrast, both indices decrease by 17%‑20% at 75°. Installing an agitator mainly improves the discharging performance under poorly‑flowing conditions: the mean velocity rises by 20.4% and the number of discharged particles increases by 4.2% at the taper angle of 75°, while the improvement is less than 1% for 60° and 90°. Within the investigated rotational‑speed range of 3‑20 r/min, the agitator speed exerts a weak effect on discharging capacity, with maximum variations of 0.3% for mean velocity and 1.1% for particle outflow count. 10 r/min is the relatively preferred value, yet higher rotational speed aggravates the dispersion of outlet particle velocity and impairs feeding uniformity. Accordingly, a feeding scheme with a 60° hopper taper angle and an agitator operating at 10 r/min is determined. Restricted by the short simulation duration and single‑sphere particle model, the obtained results serve as relative comparisons under identical initial conditions, and the absolute flow rate needs to be calibrated via prototype tests.
Downloads
References
[1] Li, M. (2020). Design and development of testing machine for mine double-tooth roller crusher. (Master’s thesis). Shandong University.
[2] Tran, V. T., Bui, N. T., & Bui, T. A. (2023). Application of EDEM simulation for calculating and optimizing a closed coal fly ash screw conveyor. Applied Sciences, 13(22), Article 12169. https://doi.org/10.3390/app132212169
[3] Rhymer, D., Ingram, A., & Windows-Yule, C. R. K. (2025). A barrel shape study for a twin-screw conveyor using the Discrete Element Method. Powder Technology, 455, Article 120744. https://doi.org/10.1016/j.powtec.2025.120744
[4] Pezo, M., Pezo, L., Lončar, B., Kojić, P., Ilić, M., & Jovanović, A. (2025). Granular flow in screw conveyors: A review of experiments and discrete element method (DEM) studies. Powder Technology, 459, Article 121040. https://doi.org/10.1016/j.powtec.2025.121040
[5] Yue, Y. S., Yang, P., Shen, X. B., Wu, Z., & Fang, M. M. (2022). Design and application of control system for high precision quantitative feeder. Resources Environment & Engineering, 36(6), 843–849.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 International Core Journal of Engineering

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.




